Use the following guide to set up a Smart System that consists of a Gateway, at least one thermostat, and at least one wireless StatLink module.

43301 Wireless Gateway included parts:
  • Wireless Gateway.
  • Mini USB to Micro USB cable.
  • USB power adapter.
  • Ethernet cable.
  • Printed instructions.
Wireless Gateway Parts

46801 Wireless Thermostat included parts:
  • Wireless Thermostat
  • 4 x AAA batteries
  • Mounting screws
  • Printed instructions

T-stat parts

40328 8 Zone Wireless Module included parts:
  • Wireless StatLink module with cover
  • Printed instructions
StatLink parts

1 2
43302 Wireless Relay included parts:
  • Wireless relay
  • Printed instructions
  • Mounting screws
Relay Parts

  • Remove the port cover from the bottom of the Gateway by twisting 1/8 of a turn counter-clockwise and pulling out.
Twist Port Cover
Remove Port Cover

Install Power – Offline Use
  1. Plug the micro USB end of the power cable into the gateway.
  2. Plug the USB end of the power cable into the plug adapter.
  3. Plug the adapter into the wall outlet.
Offline Power Connection

  • Remove thermostat from mounting plate – pull out from bottom.
  • Use the included screws to mount the backplate to the wall in the desired location.
  • Install the included 4 AAA batteries into the thermostat.
  • The thermostat will run through the start up sequence.
  • The thermostat is now ready for pairing.
Remove cover 1
Remove cover 2
t-stat-batteries
Replace cover

Mount the Wireless StatLink Module using DIN Rail
  • Attach the DIN rail to the wall or a backing board in an appropriate location, ensuring it is level.
  • Clip the StatLink onto the DIN rail.
mount-statlink

Mount the Wireless StatLink Module to the Wall
  • Remove the terminal block from the casing by removing the screws [as marked]. Then use the mounting screws to attach the casing to the wall or backing board, ensuring it is level [note the mounting holes].
  • Replace the terminal block into the casing, securing all screws.
Remove screws

1 2 3

Though the StatLink communicates wirelessly with the thermostats, it does require hard-wiring to any zone actuators, the heat source, pump(s), dew sensors, and changeover valves.

  1. Wire the actuators to the appropriate zone terminals (see manufacturer instructions for actuator installation procedure).
  2. Clip the wires into the strain reliefs.
  3. Wire the heat demand, pump, and optional dew point switch and heat/cool changeover.
  4. Wire the 24VAC power source (not included)
StatLink wiring diagram
Wiring guidelines

Installation – Wireless relay
  • Remove the screws at the bottom.
  • Lift off the top half of the relay.
  • Remove the plastic knockouts on the bottom of the unit as necessary using wire snips.
  • Mount to the wall or backing board in the desired location.
Remove screws
Remove cover
Remove knockouts for wiring
Mount to wall

Relay Wiring – Single Room Switching (RX2)
  • Move the switch to the RX2 position.
  • Wire the relay for single room switching as per the wiring diagram. Refer to the device instructions for details.
  • Secure the wiring with the strain relief.
Relay Parts
RX2 switch
RX2 switch detail
RX2 Wiring

  • Replace the cover
  • Tighten the screws
Relay Parts
Replace cover
Replace screws

Follow these procedures for pairing the devices in your Smart System. Depending on the complexity of your heating system, it is recommended that you pair each device at the same time in a single room, labeling each thermostat, WVA, and StatLink to ensure that when they are installed they are installed in the correct location.

  • Press the multi button on top of the gateway for ~5 seconds, or until the LED flashes red.
  • Release the multi button.
LED solid red
Press multi button (enter pair mode)
LED flashes red

  • Plug in the relay.
  • The LED will flash red, indicating it is ready to be paired.
LED flashing red
LED solid red

  • The Statlink module is ready to pair as soon as power is applied to the module. It will pair automatically once the Gateway has been put into pair mode.
Network Status LED flashing 1:1
Network Status LED flashing 1:1 detail

To configure for Underfloor heating:

  • Use the Left/Right arrow keys to navigate to the USE menu.
  • Press [check] to accept.
  • The thermostat is recognized by the Zigbee network.
  • Press to accept.
  • Use the Up/Down arrows to select the Wiring Center
  • Press to accept.
Prog accept
Prog right arrow
rLay accept
join

  • The Network Status LED will turn solid green once it is paired with the system.
Network Status LED solid
Network Status LED solid detail

To configure for a radiator system:
  • Use the Left/Right arrow keys to navigate to the USE menu.
  • Use the Up/Down arrow keys to navigate to rAd.
  • Press [check] to accept.
Accept the programmable thermostat configuration
Press the right arrow tot navigate to the USE menu
Press the Up arrow to select rAd

1 2
  • Press the Pairing button for 10 seconds
  • The LED will flash red
Press the Pairing Button for 10 seconds
LED flashes red

  • The thermostat is recognized by the Zigbee network.
  • Press to accept.
  • Press the right arrow to search for the wireless valve actuator in pairing mode.
  • The prefix will be automatically selected based on the number of WVAs paired.
  • When finished pairing the actuators, press to accept to exit pairing mode.
Accept pairing mode
Press the right arrow to search for the wireless valve actuator
Accept the TRV prefix, and exit pairing mode
The pairing process is now complete

For instructions on setting up the thermostat programming click here.

Click here for Troubleshooting

Comments are closed, but trackbacks and pingbacks are open.